Epoxy Flooring VaughanResin floor coatings

Residential garages · Concord

Garage epoxy flooring in Concord

Concord is mostly employment land, so the housing pockets up toward Rutherford are smaller than in the communities around it. What that means for garages is that a higher proportion of the ones we are asked about are working garages: somebody's tools are in there, a work van parks in it, or it doubles as storage for a trade. That changes what the floor has to survive.

A garage that holds equipment rather than a family car is closer to a small workshop than to a showpiece floor, and it is quoted that way.

Tell us about the garage.

Bay count and what actually lives in there. A garage full of tools needs a different topcoat to one that holds two cars.

A car count is enough.

What is stored in there, anything already on the floor, and your timing.

We reply by email. Read how requests are handled in our privacy notice.

Garage sequence

What our garage epoxy flooring process looks like in Concord

The sequence is the same as any garage. What changes is the specification at the end of it, because a floor carrying tools and a van is being asked to do more than hold a car.

  1. Establish how it gets used

    Parking, storage, or actual work. A floor that takes dropped tools, jack stands and a loaded van wants a different build to one that sees two cars and a bicycle.

  2. Clear and assess the slab

    Everything standing on the concrete comes out so the machines can reach the wall line, and the slab underneath gets checked for previous coatings, oil contamination and cracking.

  3. Build for the duty

    A heavier topcoat where tools get dropped, oil resistance where a vehicle is worked on, and anti-slip where the floor gets wet. These are choices rather than upgrades sold by default.

  4. Install and cure

    One continuous sequence, then the dates for walking on it, putting the shelving and equipment back, and driving on it.

Oil is the specific issue in a working garage. Where a vehicle has been serviced on the slab for years, the contamination goes deeper than the surface and has to be drawn out before coating rather than washed off, and that is worth establishing before the quote is fixed.

Coverage

Other areas we serve around Concord, Ontario

Residential work is a smaller share of the schedule here than in the surrounding communities, where most of the garage and basement floors sit.

Vaughan and nearby neighbourhoods

What we install here

Other Services We Provide in Concord

Where a garage is being used for a trade, the same questions apply to any other concrete on the property.

Why us

Why choose us for garage epoxy flooring in Concord

A working garage is not a harder floor to coat, it is a different floor to specify.

  • Impact, not just tyres

    Tools get dropped

    A garage used for work takes point impact that a parking bay never sees. A dropped wrench, a jack stand or a bench leg concentrates force into a small area, so the topcoat is chosen for hardness and the build for depth, rather than for the finish that photographs best.

  • Oil

    It goes further in than it looks

    Where a vehicle has been serviced on the slab, oil migrates into the concrete over time. Cleaning the surface does not remove it, and a coating over contaminated concrete will not bond. Drawing it out is a separate preparation step, and whether it is needed changes the quote.

  • Anti-slip where it matters

    A working floor gets wet

    A garage that a work van comes into brings water and slush with it, and a glossy floor in that situation is a hazard. Aggregate goes into the topcoat where the vehicle stands and where people walk, which is a small cost and the most practical decision on the whole floor.

Questions we actually get

Concord garage questions.

I service my vehicle in the garage. Will oil ruin the coating?
Not once it is on. A cured resin floor resists oil well and cleans up easily, which is one of the main reasons to coat a working garage. The problem is oil already in the concrete before installation, since a coating cannot bond through it. That has to be drawn out during preparation.
My van drips and the floor is stained. Can that be removed?
Surface staining comes off during grinding. Deeper contamination needs a degreasing step and sometimes removal of the top layer of concrete, which is assessed before quoting. It is one of the few things that genuinely cannot be judged from a photo, since a stain that looks bad may be shallow and one that looks faint may not be.
What finish suits a garage full of tools?
A flake or quartz broadcast with a hard topcoat. Both hide marks, provide grip and take impact well. Metallic is the wrong choice in a working garage, not because it is fragile but because it shows every scuff, and it is a lot of money to spend on a surface that is about to have a toolbox dragged across it.
Do I need to empty the whole garage?
Everything standing on the floor, yes, including benches and shelving units if they sit on the slab rather than the wall. Anything wall-mounted can stay. For a working garage that is usually the biggest single task in the job, and it is worth planning a day for it.
Is anti-slip worth adding?
In a garage a work vehicle uses, yes. Water and slush come in with the van, and a smooth coated floor when wet is genuinely slippery. The aggregate is barely visible, adds very little to the price and is the sort of thing people are glad of in February.
Can you coat around a workbench that is bolted down?
Yes. It gets masked and the floor is cut in around the legs or the base. It adds edge work, which is quoted rather than absorbed. If the bench can be moved even temporarily the floor comes out better, since a continuous surface has no joints to collect debris.

Get a working garage specified for the work.

Send the bay count and what actually lives in there. The build follows the use rather than the catalogue.

Request a written quote

Free written quoteVaughan & York Region

Get a quote