Epoxy Flooring VaughanResin floor coatings

Commercial · Vellore Village

Commercial epoxy flooring in Vellore Village

A good deal of the commercial work in the newer Weston Road plazas is first fit-out. The unit is handed over as a bare slab and everything after that is the tenant's decision, including the floor. That is the best position anyone can be in, because the floor can go down before the fixtures rather than being worked around them, and it almost never happens that way.

Coating an empty unit before fit-out is faster, cheaper and neater than coating the same unit afterwards. It is worth raising with whoever is planning the build-out.

Tell us about the unit.

Floor area, what the space will be used for, and whether the fit-out has started. That last one changes the price more than most people expect.

Square footage of the area to be coated.

Intended use, fit-out timeline, and who is coordinating the build-out.

We reply by email. Read how requests are handled in our privacy notice.

Fit-out sequence

What our commercial epoxy flooring process looks like in Vellore Village

The order below assumes the best case, which is an empty unit, and explains what changes as the space fills up.

  1. Get in before the fixtures

    An empty unit has no shelving, counters or partitions to cut around and nothing needing protection. The same floor coated after fit-out costs more and takes longer, entirely because of edge work.

  2. Specify for the finished use

    A unit is a bare box until somebody decides what happens in it. Traffic, cleaning regime and slip requirements all follow from the intended use, so the floor is specified against the plan rather than against the empty room.

  3. Coordinate with the build-out

    Floor coatings sit at a specific point in a fit-out programme, generally after rough-in and before finishes. Getting that slot agreed early avoids the floor being squeezed into whatever gap is left.

  4. Install and hand over

    The build goes down in one sequence, and you get the times for foot traffic and for bringing fixtures and equipment in.

Developer slabs are often finished smooth and may carry a curing compound, so an empty unit still needs full mechanical preparation. Bare does not mean ready, it just means unobstructed.

Coverage

Other areas we serve around Vellore Village, Ontario

Newer commercial units in this part of the city are usually straightforward floors in accessible buildings, which makes them quicker than equivalent work in older premises.

Vaughan and nearby neighbourhoods

What we install here

Other Services We Provide in Vellore Village

A unit taken from bare slab often has a back area, a washroom and a customer-facing space that all want different floors. Each gets specified for what it will carry.

Why us

Why choose us for commercial epoxy flooring in Vellore Village

First fit-out is the cheapest and easiest moment to coat a commercial floor, and it is routinely missed.

  • Empty is cheaper

    Edge work is what costs

    Coating an open slab is largely uninterrupted work. The same floor with counters, partitions and shelving on it becomes a perimeter job, and perimeters are slow. The difference between coating before and after fit-out is real money, and it is almost entirely in that.

  • Specify to the plan

    Not to the empty room

    A bare unit gives no clue what will happen in it. A clinic, a gym and a stockroom all want different surfaces, and the only way to get that right is to specify against the intended use rather than the current one.

  • Bare is not prepared

    Developer slabs still need grinding

    A brand-new slab is typically smooth and may have been sprayed with a curing compound. Neither is visible and both prevent bonding. An empty unit saves time on obstructions, not on preparation, and any quote that suggests otherwise is skipping the part that matters.

Questions we actually get

Vellore Village commercial questions.

We just took a unit as a bare slab. When should the floor go in?
Early, and usually right after rough-in. That way the slab is open, there is nothing to cut around and the trades that follow work on a finished floor rather than a dusty one. It needs protecting after installation, which is straightforward and far cheaper than coating around fixtures later.
Is it much cheaper than doing it after we are set up?
Meaningfully so, and the reason is edge work rather than a discount. An open floor is laid in long uninterrupted runs. A fitted-out floor is a series of cut-ins around counters and partitions, each of which is slow. The gap is usually large enough to be worth reordering the programme for.
Does our landlord need to approve it?
For a leased unit, almost certainly, since most leases treat a floor finish as an alteration. It is worth confirming before you get far. We can supply the specification and a description of the work for you to submit, which is normally what is asked for.
The unit is brand new. Does it still need full preparation?
Yes. New commercial slabs are often power-floated to a smooth finish and sometimes sprayed with a curing compound, and both leave a surface a coating cannot grip. Empty saves time on obstructions, not on grinding. That distinction is where corners get cut.
We are not sure what the space will be used for yet.
Then it is worth waiting on the specification, though not necessarily on the work. A general-purpose build suits most uses and can be topcoated later for a specific requirement. What we would avoid is guessing at a slip rating or a chemical exposure that has not been decided.
Can you coat the back area and the customer area differently?
That is usually the sensible approach. A stockroom needs durability and nothing more, while a customer-facing floor is judged on appearance. Specifying them identically means overspending on one or underspending on the other, so they are quoted as separate areas.

Coat the unit before the fixtures go in.

Send the area, the intended use and where the fit-out is up to. The earlier this lands, the cheaper it is.

Request a written quote

Free written quoteVaughan & York Region

Get a quote